Because it does all of the cutting, the circular saw blade is an essential part. The blade rotates at a speed of approximately 3,000 to 5,500 revolutions per hour (rpm) when you use this power tool. Although this may seem like a lot, if your hand is caught in the blade’s rotating mechanism, then injuries can occur.
It’s no surprise that people are afraid to use this tool because of its high rpm.
Here’s the good news. You won’t have any problems with your circular saw in the future if you know how to service it properly. After cutting something, one of the most common issues users have is to remove a stuck blade.
Preventing Accidents While Removing Blades
- Before you attempt any maintenance or removal of the blade, unplug your circular saw. Turn off the switch after unplugging it. Do not let go of the switch for more than five seconds. It can still be accidentally turned on even if it is off.
- To protect yourself against flying debris, wear safety glasses. You should also wear breathing protection when working with power tools. Dust is released into the atmosphere.
- Place the circular saw on a workbench or table that has enough space for your extensions and hands. When removing the blade, make sure it is stable enough to not rock.
- Find the arbor bolt that holds the blade in place. It is located at the back of the tool, near the on/off switch. This bolt is used to secure all types of blades, so make sure you look out for it whenever you remove any replacement blade.
- If there is one, use one hand to grasp the handle. Secure it. You can use your other hand to secure the arbor bolt using a wrench or ratchet depending on how large the arbor bolt is.
- You can turn the tool off by applying steady pressure. At the same time, use your free hand to turn the arbor bolt counterclockwise. You will notice a slight play in your blade after turning it about half a turn.
- Hold onto the blade with your other hand and turn counterclockwise to pop it off. Keep doing this until the four sides of the circular saw are removed. You don’t want it to turn any more.
You now know how to safely remove circular saw blades without causing injury to yourself or the blade. These steps can be used with any type of power tool that has a circular saw blade. Keep them in mind if you need a replacement blade, or if one gets stuck inside of your power tools.
How Do You Remove The Circular Saw Blade From A Circular Saw?
- Before removing the blades, make sure you turn off the power. It can still turn on even if the switch is off. So don’t forget to press the button!
- Wear safety glasses to protect your eyes from debris while using power tools. When working with dust from cutting or grinding, it is recommended to wear a respirator.
- The tool should be placed in an area that allows for one hand to reach the back handle, if one is present. However, it should not rock when trying to remove stuck blades. The tool must be placed so that the four sides of each blade aren’t blocked by anything.
- Locate the arbor bolt with one hand and hold it in your other hand. You can use a wrench to turn the blade counterclockwise.
- As you pull the arbor bolt out, keep your grip on the handle and turn it counterclockwise. Keep going until you have removed all four sides. Otherwise, it will turn counterclockwise.
- After the blade is free of any movement, you can slowly take it off by pulling on the handle. Keep your other hand on its front handle in case of emergency.
A Video Guide On How To Remove Circular Saw Blade
This video will show you how to remove and replace a circular saw blade.
How To Remove A Circular Saw Blade
Step:1
It should be unplugged.
Step:3
Place the tool so that there is enough space for one hand near to the back handle, and enough for the four sides of your blade not to be blocked by anything.
Step:4
Locate an arbor bolt, and then use a wrench to turn the wrench counterclockwise until there is some play in your blade.
Step:5
Continue to turn counterclockwise, pulling the arbor bolt a little so there is no movement.
Step:6
Once the blade is free of any movement, you can slowly take it off by pulling on the handle and keeping your other hand on its front handle.
How Can You Safely Remove A Circular Saw Blade Using Power Tools?
- Before removing the blades, make sure you turn off the power. It can still turn on even if the switch is off. So don’t forget to press the button!
- Wear safety glasses to protect your eyes from debris while using power tools. When working with dust from cutting or grinding, it is recommended to wear a respirator.
- The tool should be placed in an area that is large enough to hold one hand, but not so heavy that it will tip over when trying to remove stuck blades. You must place it where the blade’s four sides aren’t blocked by anything. Also, you don’t need to have enough space for just one side.
- Locate the arbor bolt with one hand and hold it in your other hand. You can use a wrench to turn the blade counterclockwise.
- As you pull the arbor bolt out, keep your grip on the handle and turn it counterclockwise. Keep going until you have removed all four sides. Otherwise, it will turn counterclockwise.
- After the blade is free of any movement, you can slowly take it off by pulling on the handle. Keep your other hand on its front handle in case it becomes loose.
Replace Blades Can Be Used In A Variety Power Tools, Including The Table Saw, Band Saw, And Circular Saw.
You can do it yourself, but if you have a problem, it is better to call a professional. This job requires the use of specific tools and carries a high chance of injury. Before you can remove the final face, you will need to first remove the four sides of each side of the circularsaw blade.
First, remove the safety guards from the circular saw blade. Next, disconnect the power source from the motor to ensure that no current is being applied to it. Next, you must turn off the switch locking mechanism that is associated with your machine. To ensure the blade isn’t blocked, turn it by hand.
After you’ve done that, you can start to remove the circular saw blade from each side using a flat-head screwdriver. To gain access to the cutting area of your circular saw, you will need to open any access panels. You may have to use a sledgehammer or woodblock to dislodge your blade if the housing is not easy to remove.
Conclusion:
When removing a circular-saw blade, it is best to use several methods. Begin by taping the blade with a hammer. If this fails, you can use a wrench or a hammer to loosen the blade. If neither of these methods work, you can try a wrench to loosen the bolt. Take your time and be careful when doing this job.
